MARKETPLACC ONLINE STORE

E27 Construction Lamp Holder with 12 cm Cable and Connector – White

User Manual

📑 Table of Contents

Main Features
Installation and Usage Steps
Important Safety Information
Cleaning and Maintenance
Product Specifications
Helpful Tips
Troubleshooting

💡 Main Features

E27 construction lamp holder designed for temporary lighting installations.
A practical lighting solution for construction sites, renovations and other installation work.
Compatible with standard E27 light sources.
Features an integrated 12 cm cable.
An electrical terminal connector is attached to the end of the cable.
White colour with a compact design.
IP20 protection rating, suitable for dry indoor environments.
The product contains one construction lamp holder.

⚙ Installation and Usage Steps

Before use, inspect the lamp holder, cable and terminal connector. Do not use the product if any part is damaged or cracked.
Make sure that the electrical supply to which the product will be connected is rated at 230 V / 50 Hz.
Before installation, switch off the relevant electrical circuit and verify that the power supply is disconnected.
Connect the terminal connector at the end of the lamp holder cable to the properly prepared electrical wires.
The electrical connection must be carried out by a suitably qualified person in accordance with applicable regulations.
After connecting the wires, check that they are securely fixed and that no conductive parts are exposed.
Restore the power supply only after installation is complete, all connections have been checked and protective covers are properly fitted.
Insert or remove the E27 light source only when the power supply is disconnected.
During use, ensure that the product is not exposed to water or moisture.

⚠ Important Safety Information

This product is designed for a 230 V / 50 Hz electrical supply. Mains voltage can cause a life-threatening electric shock.
Always disconnect the power supply before carrying out any installation work.
Verify that the circuit is completely de-energised before starting installation.
Electrical wiring connections must be performed by a suitably qualified person.
The product has an IP20 protection rating. It is suitable only for dry indoor environments protected from moisture.
Do not use the product outdoors, in damp rooms, in areas exposed to direct water or in locations where the lamp holder may become wet.
Do not use the product if the cable, housing or terminal connector is damaged.
Do not modify, alter or dismantle the electrical components of the product.
Never touch the connectors or conductive parts while the product is energised.
Always disconnect the power supply before replacing the light source and allow the bulb to cool down.
Use only light sources with a suitable E27 base.
Do not use the product with an electrical supply that differs from its rated voltage.
If you notice unusual overheating, a strange smell, discolouration or sparking during operation, disconnect the power immediately and stop using the product.

🧼 Cleaning and Maintenance

Before cleaning, disconnect the power supply and make sure the product is de-energised.
Clean the exterior of the lamp holder with a soft, dry cloth.
Do not use water, wet cleaning products or liquid cleaners on the electrical components.
Do not use corrosive chemicals, solvents or abrasive cleaning materials.
Regularly inspect the cable, lamp holder and terminal connector for damage.
Make sure that the connections remain secure and that the cable is not damaged or bent excessively.
Store the product in a clean, dry place protected from moisture.
Do not continue using a damaged or deformed lamp holder.

ℹ Product Specifications

Property	Value
Product Name	E27 Construction Lamp Holder with 12 cm Cable and Connector – White
Product Type	Construction Lamp Holder
Brand	Eko-Light
Model	EK1091
Socket Type	E27
Rated Voltage	230 V / 50 Hz
Cable Length	12 cm
Protection Rating	IP20
Height	80 mm
Width	37 mm
Depth	37 mm
Colour	White
Certification	CE Marking
Sales Unit	1 piece

💡 Helpful Tips

The construction lamp holder is a practical solution for locations where temporary lighting is required during work. Before use, always check that the lamp holder is suitable for the electrical supply to which it will be connected.

The lamp holder has an E27 socket, so the selected light source must also have an E27 base. The rated voltage of the light source must be compatible with the 230 V electrical supply.

Due to its IP20 protection rating, the product must only be used indoors in dry environments protected from moisture. Do not install the lamp holder in locations where it may come into contact with water or moisture.

🔧 Troubleshooting

Problem	Possible Cause	Solution
The light source does not illuminate	The light source is faulty, not properly inserted or not receiving power	Disconnect the power supply. Check that the light source is correctly fitted and in good condition. The electrical connection must be inspected by a suitably qualified person, with the circuit de-energised.
The light source does not fit into the socket	The light source does not have an E27 base	Do not force the light source into the socket. Check the base type and use a compatible E27 light source.
The cable or terminal connector is damaged	Mechanical damage, a broken cable or a deformed connector	Stop using the product. Do not attempt to repair or modify damaged components yourself.
The electrical connection becomes loose	Improperly secured wires or a damaged terminal connector	Disconnect the power supply and have the connection checked by a suitably qualified person.
The lamp holder has been exposed to moisture	Use in an unsuitable environment	Disconnect the power supply immediately. Do not use the product until its electrical safety has been checked.
The lamp holder overheats or produces a burning smell	A faulty light source, poor connection or electrical malfunction	Disconnect the power supply and stop using the product. Have the electrical connection inspected.